← Latest papers
📄 plant biology

Secondary growth in the tomato stem is suppressed by the flowering regulators FUL2 and STM3

This study reveals that the tomato flowering regulators FUL2 and STM3 physically interact to form a complex that represses secondary xylem growth in a stage- and position-dependent manner by suppressing specific NAC and MYB transcription factors.

Original authors: Pandey, K., Appiah, A. P., van Velzen, R., Zahn, I. E., Basu, E., Angenent, G. C., Deuss, P. J., Bemer, M.

Published 2026-11-06
📖 6 min read🧠 Deep dive

Original authors: Pandey, K., Appiah, A. P., van Velzen, R., Zahn, I. E., Basu, E., Angenent, G. C., Deuss, P. J., Bemer, M.

Original paper licensed under CC BY 4.0 (https://creativecommons.org/licenses/by/4.0/). ⚕️ This is an AI-generated explanation of a preprint that has not been peer-reviewed. It is not medical advice. Do not make health decisions based on this content. Read full disclaimer

Plants grow in two distinct ways. First, they stretch upward, reaching for the sun through primary growth driven by tips at the top of the stem. Second, they grow wider, thickening their trunks and branches through secondary growth. This widening is powered by a thin, active layer of cells called the vascular cambium, which acts like a factory floor, constantly producing new wood toward the inside and new bark toward the outside. While this process is familiar in trees, creating the massive trunks we see in forests, it also happens in many softer, herbaceous plants like tomatoes. In these crops, the stem does not just get taller; it accumulates layers of wood to support the heavy fruit and transport water. Understanding how a plant decides when to thicken its stem and when to stop is crucial, because this balance determines how much biomass a plant produces and how well it can withstand stress.

For a long time, scientists knew that flowering and stem thickening are connected, but the exact molecular switches controlling this in crops like tomatoes remained a mystery. In the model plant Arabidopsis, certain genes that tell a plant when to flower also act as brakes on wood formation. Researchers wondered if a similar system existed in tomatoes, which produce much more wood than Arabidopsis. A team of scientists set out to map the genetic activity inside the tomato stem with extreme precision, looking for the specific genes that turn wood production on or off. They discovered that two specific genes, which are famous for their role in starting the flowering process, also serve as powerful brakes on the thickening of the stem.

To find these hidden regulators, the researchers first needed to see exactly which genes were active in the different layers of the tomato stem. They used a technique called laser capture microdissection, which allows scientists to use a laser to cut out tiny, specific strips of tissue from a plant stem under a microscope. They collected samples from the cambium, the wood, and the outer layers of 60-day-old tomato plants. By sequencing the genetic material from these isolated pieces, they built a detailed map of which genes were working where. This map confirmed that the basic genetic machinery for making wood in tomatoes is very similar to that in trees like poplar. However, the map also revealed something unexpected: two genes known for controlling flowering, named FUL2 and STM3, were highly active inside the wood and the cambium layers.

The team then tested what would happen if they removed these two genes. Using a gene-editing tool, they created tomato plants where FUL2, STM3, or both were switched off. When these mutant plants grew, the results were striking. The stems of the mutant plants, particularly near the base, became much thicker with wood than the normal plants. In fact, the area of wood in the mutant stems doubled compared to the wild type. This proved that FUL2 and STM3 normally act as repressors, holding back the production of secondary xylem. The researchers found that these two genes work together as a team; removing just one of them was enough to cause a significant increase in wood, and removing both did not make the effect much stronger. This suggested that they function as a single complex, physically interacting to keep wood formation in check.

The study also uncovered that this genetic control is not a simple on-off switch that happens at a single moment. The researchers tracked the plants over time, from young seedlings to mature plants. They found that the expression of FUL2 and STM3 remains low when the plant is young and only rises significantly after the plant has already transitioned to flowering. This timing indicates that the genes do not simply react to the moment a flower appears, but rather become active as the stem matures. Furthermore, the genetic response to losing these genes changed depending on the age of the plant and the position on the stem. In younger parts of the stem, the loss of these genes triggered a specific set of other genes related to wood formation. In older, more developed parts of the stem, a different set of genes was affected. This means the plant uses these flowering regulators to fine-tune wood production continuously as the stem grows, adjusting the balance of growth based on the local needs of that specific section of the stem.

The findings also shed light on the chemical composition of the stems. The mutant plants with increased wood production contained significantly more lignin, a tough polymer that gives wood its rigidity. In one of the mutant lines, the lignin content rose from about 11.8 percent in normal plants to 16.3 percent, a substantial increase that would make the stem much harder and more woody. This confirms that the genes are not just controlling the amount of wood but are also influencing its quality. The researchers observed that the genes FUL2 and STM3 are active not just in the wood itself, but also in the ray cells, which are living tissues that run radially across the stem, connecting the inner wood to the outer bark. This positioning suggests these genes might be helping to maintain the living connections within the stem while simultaneously preventing the wood from becoming too dense too quickly.

Ultimately, this research reveals a sophisticated link between a plant's reproductive life and its structural support. The same genes that help a tomato plant decide to flower also step in later to limit how much wood the stem produces. By repressing a suite of other genes that drive wood formation, FUL2 and STM3 ensure that the stem does not become overly woody, which might be detrimental to a herbaceous crop. The study provides a clear picture of how a plant coordinates its growth, showing that the transition to flowering is not just a change in the top of the plant but a signal that ripples down the stem to reshape its very architecture. This knowledge offers a new window into how crops manage their resources, balancing the need to support fruit with the need to remain flexible and efficient.

Drowning in papers in your field?

Get daily digests of the most novel papers matching your research keywords — with technical summaries, in your language.

Try Digest →