← Latest papers
🔬 applied physics

Controlled spin-torque driven domain wall motion using staggered magnetic nanowires

This paper demonstrates that controlled domain wall motion using spin-transfer torque can be achieved in staggered magnetic nanowires, where key properties like depinning current and thermal stability are tunable via device dimensions, offering a promising solution for high-capacity racetrack memory applications.

Original author: H. Mohammed, S. Al Risi, T. L. Jin, J. Kosel, S. N. Piramanayagam, R. Sbiaa

Published 2026-11-09
📖 5 min read🧠 Deep dive

Original author: H. Mohammed, S. Al Risi, T. L. Jin, J. Kosel, S. N. Piramanayagam, R. Sbiaa

Original paper licensed under CC BY 4.0 (http://creativecommons.org/licenses/by/4.0/). ✨ This is an AI-generated explanation of the paper below. It is not written or endorsed by the author. For technical accuracy, refer to the original paper. Read full disclaimer

In the quest to store more information in smaller spaces, scientists have long looked beyond the spinning disks of traditional hard drives toward a concept known as racetrack memory. Imagine a long, narrow magnetic wire where data is not stored on a flat surface but is instead encoded as a series of tiny magnetic regions, or domains, lined up along the length of the wire like cars in a traffic jam. To read or write this data, these magnetic regions must be moved precisely along the track. The challenge lies in controlling their movement; if they slip too far or stop in the wrong place, the information becomes corrupted. Researchers have tried to solve this by creating physical bumps or steps in the wire to act as parking spots, hoping to hold the magnetic regions in place. However, moving these regions using magnetic fields alone is often too slow or imprecise for practical devices. A more promising approach involves using a stream of electrons, which carry a property called spin, to push the magnetic regions along the wire. This technique, known as spin-transfer torque, offers a way to move data with electricity rather than bulky magnets, but getting the regions to stop exactly where intended remains a difficult puzzle.

A team of researchers set out to solve this puzzle by designing a new type of magnetic wire with a staggered, or stepped, shape. They built these devices using a stack of cobalt and nickel layers, materials chosen for their ability to maintain a strong magnetic orientation perpendicular to the surface. The wires were crafted to be about 50 micrometers long and 1 micrometer wide, with specific sections offset to create a series of steps. To test how well these steps could control the magnetic regions, the scientists used a powerful microscope that detects magnetic fields through light, allowing them to watch the movement of the domain walls in real time. They began by testing a standard, straight wire without any steps. When they applied a magnetic field to flip the magnetization, the change happened all at once, jumping instantly from one state to another. No matter how carefully they adjusted the field, they could not stop the magnetic region in the middle of the wire; it simply refused to stay put.

The researchers then turned their attention to the stepped wires. When they applied a magnetic field to these devices, the behavior changed dramatically. Instead of flipping all at once, the magnetic state changed in distinct jumps. The first jump occurred when a magnetic region formed at the start of the wire and stopped at the first step, held there by the physical change in the wire's shape. A second jump happened at a slightly higher field, creating a new region on the other side of the wire. This confirmed that the steps could act as barriers, holding the magnetic regions in place. However, relying solely on magnetic fields to move the regions from one step to the next proved difficult to control, as the steps were identical in size and offered the same amount of resistance.

To achieve precise control, the team introduced an electric current. They first used a small magnetic field to create a single magnetic region near the start of the wire and then removed the field entirely. They then sent short pulses of electricity through the wire. When the current reached a specific strength, the magnetic region would jump from the first step to the second. By carefully adjusting the amount of current, they could move the region to the third step and beyond. The researchers found that the exact amount of current needed to move the region depended on the dimensions of the steps and the presence of a small assisting magnetic field. In some designs, the current required to move the region changed significantly with the magnetic field, while in others, it remained more stable. Crucially, once the region was moved to a step, it stayed there. The team left the device for several hours and observed no change in the position of the magnetic region, proving that the steps could hold the data securely without the need for constant power.

The study also looked at how long these magnetic positions could last under different conditions. They found that the time it took for a magnetic region to slip off a step followed a predictable pattern related to the strength of the magnetic field and the stability of the material. By tweaking the design of the steps, such as changing their width or the distance between them, the researchers could adjust how much current was needed to move the data and how stable the data remained. This work demonstrates that by combining a specific wire shape with electric currents, it is possible to move magnetic data with high precision and hold it in place reliably. The findings suggest that this approach could be used to fine-tune the performance of future memory devices, offering a path toward storage systems that are both high-capacity and highly controllable.

Drowning in papers in your field?

Get daily digests of the most novel papers matching your research keywords — with technical summaries, in your language.

Try Digest →